Browning 1911-22 Review

by
posted on June 15, 2011
** When you buy products through the links on our site, we may earn a commission that supports NRA's mission to protect, preserve and defend the Second Amendment. **
2011615105219-_mg_1954_f.jpg

"Isn't it just so cuuuuute?!" That was a lot of folk's reaction to the Browning 1911-22 introduced at the SHOT Show in Las Vegas in January. It was pretty much my reaction, too. When I picked it up it felt more like a 1903 Colt, but its look and operation were pure 1911. I am more than just a fan of the 1911. After nearly 40 years of owning and carrying several versions of it, I can attest that I am a true devotee of the pistol. So it's understandable how my interest was piqued when Browning announced this diminutive rimfire.

Over the years, there have been many attempts to produce a rimfire version of John Moses' most famous pistol. Those attempts have resulted in mixed success—that is to say, a lot of guys want one for a cost-effective trainer, but few are willing to tote the note for one. Unfortunately, that may be the fate of this one, if the chatter I have seen on several Internet forums is accurate. Here again, guys pine for a U.S.-built, all-steel, 1911-style .22 that groups less than an inch at 25 yards, has a 3 1/2-pound trigger pull and weighs around a pound—all for about 150 bucks or less. Dream on.

Browning did produce an accurate, scaled-down rendition of the 1911A1 that is made in the USA, weighs a hair less than a pound and is accurate enough for most rimfire chores. But its frame and slide are made from aluminum alloy, and it will set you back significantly more than a C-note and a half with an MSRP of $600. I don't have a problem with aluminum alloy in a pistol of this type, although I'd like to see a better finish than raw casting for the money.

Standard barrel length is 4 1/4 inches—the same as on a Commander, but the scaling accurately replicates a full-size 1911—and a 3.6-inch barreled compact version is planned. The pistol comes with one 10-round magazine. Made of pressed steel with a plastic follower, thumb piece and base plate, it also has a stiff spring. Grip panels are checkered plastic. The safeties replicate the GI ones in form. The manual safety—with its small, nub-like thumb piece—is more like an original 1911 than an A1, so it rests deeper in the thumb if you ride the safety while shooting. It's a mild distraction since the rimfire recoil is minimal, but it did bring back some unpleasant memories of my early shooting with full-size, as-issued .45s.The grip safety is a short-tang type, so guys with fleshy hands and those who grip it high will have to watch out for hammer bite. Operation is straight blowback, and the recoil spring is pretty substantial. That's not too surprising given that the slide is lightweight alloy and smaller.

At the range, the shorter barrel trimmed about 200 fps off what a 6-inch revolver would produce, which is to be expected. Happily, especially for plinkers, my best groups came from Federal American Eagle budget ammo. Groups averaged 1 1/4 inches at 20 yards, but Winchester Power Points were right behind it at 1 3/8 inches. Like the rest of the pistol, the sights are a scaled-down replica of the GI sights. Younger eyes might be able to cut them a bit finer and get better groups. In addition, the trigger pull was a rather stiff 8 pounds, 2 ounces. The 1911-22 isn't intended as a sophisticated target pistol, but again, for the money, I'd like to see a more reasonable trigger pull. After all, the pistol weighs 15 1/2 ounces empty.

Takedown is exactly like any other 1911. The stainless-steel barrel is slightly belled toward the muzzle to accommodate the barrel bushing. It does not appear to be fitted, as there was a very small amount of play between it and the barrel.

To date, the 1911-22 is expected to hit dealer's shelves in August. The original availability date was the first quarter of this year, but the brass at Browning decided to include a magazine safety at the last minute. So all of the pistols built are undergoing that modification.

As a devotee of the 1911, I really like this scaled-down version of my favorite semi-auto. It's a fine little plinker, and with a bit of tuning and the right ammunition, could be an excellent small-game pistol. There are a few things I think Browning will need to address to maximize the chances of its success at this price point, as previously mentioned. First, it should come with two magazines, and spares need to be readily available. Also, wood grip panels and a little better attention to the metal finish are more appropriate for a pistol of this quality. And finally, take at least 3 pounds off of that trigger.

Specifications:

Contact: 800-333-3288, browning.com
Type:
Single-action, semi-auto pistol
Chambering:
.22 LR
Barrel:
4 1/4 (tested), 3.6 inches; 1:16 RH
Trigger:
8 lbs., 2 oz.
Magazine:
Detachable box; 10-round capacity
Sights:
Fixed iron
Safety:
Manual sear block; grip safety
Grips:
Checkered plastic
Overall Length:
7 1/16 inches
Weight:
15.5 oz.
Metal Finish:
Black anodized
Accessories
: Comes with Browning zippered case
MSRP:
$600

Shooting Results:
Measured average velocity for 10 rounds from a 4.25" barrel. Range temperature: 58 degrees. Humidity: 42 percent. Accuracy for five consecutive, five-shot groups at 20 yards from sandbags. Abbreviations: LR (Long Rifle), Cu (Copper), JHP (Jacketed Hollow Point), TCHP (Truncated Cone Hollow Point), Sd (standard deviation).

 

Cartridge

.22 LR Vel. @ 15' (f.p.s.)

Energy

(ft-lbs.)

Group Size

(in inches)

   
     

Smallest:

Largest:

Average:

Federal American Eagle; 38-gr. Cu-plated lead

1,059 Avg.
15 Sd

95

1.0

1.50

1.25

Winchester Power-Point; 40-gr. JHP

1,006 Avg.
21 Sd

90

1.125

1.50

1.375

CCI SR Green 21-gr. TCHP

1,338 Avg.
33 Sd

83

1.375

2.0

 

Average Extreme Spread

 

 

1.43

 

 

Latest

Stuart 45 Pistol Pre War Manuevers Web Main
Stuart 45 Pistol Pre War Manuevers Web Main

Guns Of The U.S. Tankers In World War II

Since the end of World War II, debates have raged about the effectiveness of American armored fighting vehicles in that conflict. Despite all the Monday morning armored quarterbacking, American AFVs were war-winners, driven to victory by some the finest fighting men our nation has ever produced.

MidwayUSA Foundation Awards Over $14 Million In Cash Grants In 2025

In honor of National Shooting Sports Month—held annually in August—along with the growing popularity of the sport with new participants, MidwayUSA Foundation announced it has distributed more than $14.2 million in cash grants to support youth shooting sports in 2025.

Making The KelTec PR57 In Wyoming

To make its PR57 handgun, KelTec invested in an entirely new manufacturing facility located in Rock Springs, Wyo. "American Rifleman Television" headed out for an inside look at the company's efficient production process.

Taurus 66 Combat: A New "Fighting Revolver"

First introduced in the 1970s, the Taurus 66 Combat is a medium-frame revolver that has seen several evolutions in its lifetime, and the latest update creates what the company considers "the final word in fighting revolvers."

Review: Taurus GX2

From cars to cellphones, as a product gets more sophisticated, it usually also gets more expensive. And, as modern handguns get more modular and optic-ready, their prices tend to go up.

Rifleman Q&A: A Garand Puzzlement

"We are a father-and-son NRA member tandem in search of an answer regarding the branding of an M1 Garand rifle. We own an M1 rifle that has markings indicating it was a “lend lease to England,” and it also has a .308 barrel/sleeve."

Interests



Get the best of American Rifleman delivered to your inbox.