Rifles > Lever-Action

Taylor's Tactical Model 1892 Alaskan Take-Down

Evaluated here is Taylor’s & Company’s modernization of the Model 1892, the Alaskan Take-Down, which is distributed exclusively by Taylor’s Tactical.

Manufacturers of firearms, optics and accessories are, for good reason, increasingly modifying existing products to capitalize on the current desire for all things tactical and survival/sustenance-related. Even the Model 1892 lever-action rifle, which is among the most “traditional” of firearm designs, hasn’t escaped an overhaul to satiate the demand. Evaluated here is Taylor’s & Company’s modernization of the Model 1892, the Alaskan Take-Down, which is distributed exclusively by Taylor’s Tactical. The rifle is produced in Italy by Chiappa and imported exclusively for Taylor’s & Co.

The 1892 Alaskan Take-Down’s aesthetics and features are decidedly different than typically encountered on such rifles. Its receiver, barrel and large loop lever have a matte-chrome finish, while the hardwood stock and fore-end are covered with an overmolded rubber finish the company calls Softouch. Combined, it creates a utilitarian two-tone package that’s far from the time-honored combination of walnut and bluing, and even more durable.

Arguably, its most attractive feature is the fact it can be broken down into two separate parts that measure 20 inches in length or less for easy transport—no small consideration for those heading to the backcountry, regardless if on a bush plane or backpacking in. Thanks to some clever design features, no tools are required for takedown, either.

The procedure is simple. Check and double-check that the rifle is unloaded and leave the action open. Next, locate the 1.3-inch long, flush-fitting magazine-disassembly lever, which is at the front, bottom of the magazine tube. Grasp it on the end toward the receiver and rotate until perpendicular to the magazine. At the same time a lug will retreat from a recess under the barrel, a system that locks everything solidly in place while shooting.

Rotate the lever counter-clockwise to remove the magazine. Once it’s out, you can grasp the fore-end while firmly holding the stock, and turn counter-clockwise 90 degrees to separate the two. This is made possible by the interrupted thread pattern on the barrel and receiver. Damage to the magazine can be prevented by reinstalling it on the fore-end during storage.

Because both the front and rear sights are located on the barrel assembly, there is no point-of-impact shift resulting from the disassembly and reassembly process. The 1892 Alaskan Take-Down ships with windage- and elevation-adjustable Skinner Express sights at the rear. The test rifle had Skinner’s 0.125-inch (large) aperture installed, which is excellent for rapid target acquisition, but precision bullet placement at 100 yards and beyond is compromised. For the intended purposes of the .44 Rem. Mag.-chambered Take-Down—hunting/survival—it’s a fair trade-off; however, smaller apertures can be purchased from Skinner for $11.

The dovetailed front sight has a 0.625-inch long, red fiber-optic pipe anchored in three places. The sight is slightly more than 0.4 inches above the barrel. In testing, target acquisition was fast, intuitive and even in low light the front sight was easy to find. To mount a scout-style optic, removal of the Skinner sight is required. It occupies two of the four threaded holes provided on the rifle designed to accept Weaver 61M mounts.

At the muzzle end, the 20-inch octagonal barrel—also available in a 16-inch version—has a diameter of 0.75 inches and ends with a radius crown. At the receiver the barrel widens to 0.84 inches. Both the barrel and the receiver had an even finish with no blemishes visible.

The buttstock was a different story. A trio of nicks in the Softouch finish resulting from rough handling in transit was deep enough to expose the hardwood underneath. The semi-tacky treatment was extremely effective on the hot, humid day when accuracy and function testing were conducted. Sling swivel studs were absent; however, they can easily be added thanks to the wood buttstock and fore-end.

With the 20-inch barrel, the rifle’s overall length is 38 inches; obviously the 16-inch barreled variant’s overall length is 4" shorter. Capping the buttstock is a generous 1/2-inch thick rubber recoil pad that contributes to the rifle’s 13¾-inch length of pull.

To load the magazine, cartridges are pushed through a gate on the right side of the receiver and empty brass is ejected from the top of the receiver—it’s a system familiar to Model 1892 fans. The oversized loop lever is a handy feature, especially whenever gloves are worn. Regardless of familiarity with lever-action operation, though, no one could miss the fact that this is the kind of trigger dreams are made of—no creep, no grit, and no takeup. All rifles should have one of these, and it broke cleanly and crisply at precisely 3 pounds with regularity.

During testing the only stoppage occurred due to operator error, a failure to work the lever with enough authority when chambering a single Federal cartridge. There were no other malfunctions.

Velocities produced by what is really handgun ammunition make the rifle a viable complement to a .44 Rem. Mag. revolver in bear country or survival situations. The Softouch finish does its job, and proper sight pictures are easy to acquire with that red glow up front. Most shooters will probably agree that nothing needs to be changed.

And our sample was a real shooter. In fact, in multiple instances three out of five holes touched at 50 yards. Moving back to 100 yards to meet American Rifleman protocol, however, the groups increased a bit. That being said, the most accurate load was Hornady’s 300-grain XTP. Its single best five-shot group measured 2.71 inches, and 25 shots averaged 4.32 inches. For 75 shots with three different loads the rifle averaged 4.69 inches. Given the use of open sights and the rifle’s chambering, we found this level of accuracy acceptable.

Anyone looking for a reliable lever gun to beat the brush for big game, backup for the backcountry, or to simply punch paper, won't go wrong with the 1892 Alaskan Take-Down.

Taylor's 1892 Alaskan Take-Down
Manufacturer: Armi Sport di Chiappa, Via Milano 2, Azzano Mella, Italy, 25020; 011390309749065; chiappafirearms.com
Importer: Taylor’s & Co. (Dept. AR), 304 Lenoir Drive, Winchester, VA 22603; (540) 722-2017
Caliber: .357 Mag., .44 Rem. Mag.(tested), .45 Colt
Action Type: lever-action, center-fire repeating rifle
Receiver: matte-chrome steel
Barrel: 16 inches, 20 inches (tested), matte-chrome steel
Rifling: six-groove, 1:20-inch RH twist
Magazine: 10-round tubular
Sights: Skinner Express rear sight, fiber-optic front drift adjustable for windage: drilled and tapped for scope bases
Trigger: single-stage; 3-pound pull
Stock: hardwood with rubber overmolded Softouch finish: length of pull, 13¾ inches; drop at comb, 2 inches; drop at heel, 25⁄8 inches
Overall Length: 38 inches (20-inch barreled version)
Weight: 6 pounds, 10 ounces
Accessories: owner’s manual
Suggested Retail Price: $1,324

Share |

Comments

ADD YOUR COMMENT

Enter your comments below, they will appear within 24 hours


Your Name


Your Email


Your Comment

9 Responses to Taylor's Tactical Model 1892 Alaskan Take-Down

Tom wrote:
March 11, 2014

I had a gun shop order one for me at $1140. Have no idea when it will be available, as they are all on order, and first come first served. It only comes in a 16' barrel for this .357 model, and I wish it had an 18-20' barrel. If you compare prices, a Marlin 1894C, .357 is $750-$800 new, If you can find one, and $900-$1000 used on line. Add in the cost of a takedown, skinner sights, smooth action large lever, and a perfect trigger, you get a complete out of the box ready rifle for $1140. That is a bargain to me.. I ordered .357 because I have a J frame for concealed carry, and a Ruger GP100 also for carry, and more fire power. Having all arms fire the same ammo is nice. And the versatility of ammo is a plus too. From standard .38, to Buffalo Bore 180 gr. hard cast hunting rounds.

Jim wrote:
January 25, 2014

People who are concerned with the pricing need to understand that these are not off the shelf models. These are completely rebuilt custom models. Taylors does a lot of gunsmithing on the rifles for clean up and tune up. Compared to, say, WildWestGuns's copilot, which starts at $2,800, this rifle is actually relatively cheap. Their conversion to take down for a lever action is $600 alone. If you started with the rifle at $500, add the takedown at $600, add a trigger/action job at $250, you're already above the $1324 they're asking, before you go into the sights, stock upgrades, and refinish. You can say 'I can't afford it' and that's fine, but to say 'It's not worth it' is not true. It may not be what you want to spend for the rifle, but it's well worth the cost based on what you get.

arthur wrote:
December 02, 2013

No one asks to buy the rifle its simply a review. try to buy a new us made takedown, they are only custom and cost twice that of the chiappa

jello wrote:
November 27, 2013

Let's see, the 'American Rifleman' who rightly supports the 'National' Rifle Association is asking Americans to buy an overpriced rifle made in Italy!!?? Come on

VooDoo1 wrote:
November 24, 2013

Well guys, I want to begin by thanking all my fellow riflemen who take time to review firearms, show videos of their experiences, and share thoughts and instruction that is unavailable from the majority of people. I spent the 1300. bones that it took to buy the Taylors & Co Alaskan takedown. Yes its more money than you used to spend on these guns, but today most quality lever guns will run you 1000 $ or more. No arguing that there are cheaper deals out there but I wanted to dance with the prettiest girl at the dance :) When I unboxed the rifle it was in fully assembled. Take down was stiff as this puppy hadn't been oiled (first order of business). Looking through the rear Skinner sight at the fiber optic front sight was a wow experience. Again, this is a traditional 1892 mechanism that is a clear departure from tradition as a whole. How much would you pay for the cool take-down factor. I guarantee you that this is not going to be a Safe Queen. The rubber over mold is hardly noticeable in use. It probably will assist in gripping with hands or gloves. It is a smooth Axe to swing around on target. I cant wait to visit my brother and do some Hog busting in Texas.

Joe wrote:
October 23, 2013

Yes siree, it's a beauty alright! But $1,300. Bones? I don't think so. Like Chris says, ' I can remember when a lever action rifle was affordable to the average hunter.' Heck, you figure in the cost of ammunition (if you can find it) and that pretty much blows the fun out of ownership! That is unless you're one of those who find your pride in gloating over how much you paid for something. Too bad, I'd love to own one.

J. W. McCorkle wrote:
October 09, 2013

Beautiful, functional and very desirable. Only draw back I see is it's overpriced. At least for my budget.

Chris Wood wrote:
October 09, 2013

Looks really nice! Would love to have one. I can remember when a lever action rifle was affordable to the average hunter. Not so much anymore.

Al wrote:
October 09, 2013

Yup! I want one!